What to do if Lincoln MKC hood won’t close?
By
Vroomouk
This article will address the “Lincoln MKC hood won t close” issue. While addressing the Lincoln MKC hood fault, we will explain how to close the hood of Lincoln. In addition, we will also explain how to remove scratches, dents and bends from the hood.
What to do if Lincoln MKC hood won’t close?
- Open the faulty hood by pressing the hood latch lever
- Remove the latch from the car by removing the two bolts fitted on it.
- Remove the latch release with the help of a torque wrench.
- Wash the entire latch because the latch will have dirt responsible for the faulty latch.
- Dry the latch after washing.
- Lubricate the latch with the WD40 lubricant.
- Put the latch back on the vehicle.
The Lincoln MKC hood gets stuck and doesn’t close, mostly because of a faulty latch. Unfortunately, the hood latch fault is extremely common in the automobile industry. Hood latch is a simple component of the car, yet if it gets damaged, it can be a headache for the driver.
Troubleshooting the faulty hood of Lincoln MKC
- Open the faulty hood by pressing the hood latch lever. Then lift it to support it with the help of a hood prop rod. After this, check the hood latch for any damages.
- The best thing about the Lincoln MKC latch is that it is easily accessible. Unlike other cars, you need to reach the latch by removing the extra protective covering present on the top. You don’t need to do all this in Lincoln, as the hood latch fitment is visible.
- To remove the latch from the car, you need to unbolt the two bolts used to fit it on the vehicle. To remove these bolts, you need to have a torque wrench. With the help of the torque wrench, remove the bolts.
- Once you remove the car’s latch below the latch, you will observe a latch release attached to the bottom of the latch. Unlike other cars, the latch release cable is attached to the latch with the help of a bolt. Remove this with the help of a torque wrench. Once the bolt is removed, remove the cable from the latch, and the latch is now free to move out from the car.
- Once the latch is removed from the car, wash the entire latch because the latch will have dirt responsible for the faulty latch. Dry the latch after washing.
- Once the latch is dry, you need to lubricate the latch with the WD40 lubricant. After lubricating the latch, apply grease on the latch. Applying grease on the latch ensures that the moisture won’t enter the latch again and cause corrosion.
- Once the latch is properly lubricated, you need to put the latch back on the vehicle.
- To install the latch back on the vehicle, you need to attach the latch cable again by hooking it in the latch clip present in the latch. Once the latch cable is fixed, the bolt holds the latch cable in the correct place.
- After the latch cable is fixed on the latch, all you need to do is put the latch back on the vehicle. For putting the latch back on the vehicle, you need to bolt the latch with the help of a torque wrench.
- Once the bolt is fitted back on the vehicle, try closing the hood. If the hood closes, then the latch is fixed. Otherwise, you need to get it replaced.
Method to remove Scratches from Hood
- First, identify the scratches on the hood. After identifying the scratch, you need to rub the scratch with the help of sandpaper. Remember, the sandpaper you are using is above 1000 grit. For rubbing the surface with the help of sandpaper, you need to wet the area and rub it.
- Continue rubbing the scratch with the help of sandpaper until there is a slight taper from scratch. Use your finger to feel the rough edges, and then sand those edges as well.
- If the scratch is too deep, then fill the scratch with a coating of body putty. After putting the putty, sand the putty to get the optimum finish.
- After sanding is complete, tape the area where the sanding was done, and then apply to touch up the paint using the touch-up paint kit. Follow the tips mentioned on the touch-up kit to obtain a smooth finish.
Method to Remove dents from the hood
- If the dents present on the hood are light, tap the dent with the help of a lightweight hammer. Moreover, while tapping the hood, tap it in small intervals.
- For tackling deeper dents, you need to drill a hole in the centre of the dent using a 1/16-inch drill bit. Then thread a metal screw from the hole and pull the screw with the help of a plier.
- If there are any imperfections, hammer those out and put a dolly bag filled with steel shot behind the dent.
- If the paint is damaged around the dent, then rub the paint with the help of wet sandpaper and touch up the paint with the touch-up kit.
Method to remove bends from the hood
- Examine the hood, if the hood is completely buckled, then there is no scope of getting it repaired, but if it has buckled due to daily wear and tear, it is easy to repair.
- To fix the hood, you need to remove it from the car by unscrewing the hinges located near the windscreen. Once the hood is removed, you need to place the hood upside down on the grass or an old carpet.
- Now hammer the hood with the help of a hammer and strike the hammer with steady hits directly directed towards the bent. Knock the dents out slowly.
- After hammering the dents out, place a wood bock under the areas where the bent is large and hammer the hood. Placing a wooden block below the hood will help distribute force to a larger area.
- Once satisfied, paint the damaged area of the hood with paint similar to the car paint. Once dry, place the hood back on the car with the help of hinges. While placing the hood on the car, make sure it is aligned properly.
Conclusion
This article has explained how to fix “Lincoln MKC hood won t close”. In addition to explaining the technique for fixing the Lincoln MKC hood, we have also explained methods to remove scratches, dents and bends from the car hood.
Frequently Asked Questions (FAQ): Lincoln MKC hood won t close.
Can hood Damage be repaired?
If the car hood has sustained heavy damage, such as during a crash, then some chances of repairing the hood won’t be possible, but it can be easily repaired if the hood has suffered small damages.
Can I fix the dented car hood?
Fixing the dented car hood is easy but requires plenty of effort. To fix the dented car hood, you need to remove the hood from the vehicle and then hammer it down to achieve its shape back.
How much did it cost to fix a dent on the hood?
Fixing a dent on the hood can cost a person anything between $125-$500+. However, the final cost will depend on the process.
Can I fix an aluminium hood?
Yes, but while repairing the aluminium hood, you need to handle the hood with extreme care because repairing an aluminium hood involves different tools and extra care.
References
